Bayhorse Silver Inc.: Significant Scandium Values (Up to 26 G/T Sc) Accompany High Grade Silver, Bayhorse Mine, SA
The Scandium was identified during the assay resubmission that identified the gold values as reported in news release BHS2018-06. Preliminary metallurgical results indicate that Scandium can be recovered during the processing of the silver from the Bayhorse Silver Mine. Scandium (Sc) is a high value mineral used to produce high strength Aluminum alloys in the Aerospace Industry and is classed as a strategic mineral in the USA. The Company has submitted additional samples for metallurgical testing and recovery characteristics of the Scandium.
Scandium values are tabulated below:
Sample Type | Sc g/t |
BHS 1 Crosscut | 7 |
BHS 2 Raise Legend | 16 |
BHS 3 Legend | 5 |
BHS 4 Legend | 6 |
BHS 5 Legend | 12 |
BHS 6 Shaft Legend | 18 |
BHS 7 Legend | 10 |
BHS 10 Shaft top | 17 |
Sample Type | Sc g/t |
Shaft middle BHS 11 | 20 |
BHS 12 Shaft | 21 |
Upper raise | 11 |
Big Dog | 20 |
Chip, Legend top | 15 |
Channel Legend east | 11 |
Chip, Legend west | 24 |
Chip, Legend bottom | 12 |
Chip, Legend top west | 21 |
Chip, Legend west | 22 |
BHS 21 Chip LZ | 24 |
Sample Type | Sc g/t |
BHS 22 blast select | 26 |
BHS 23 blast select | 25 |
BHS 24 blast select | 21 |
BHS 25 blast select | 19 |
BHS 26 blast select | 26 |
BHS 27 blast select | 24 |
BHS 28 blast select | 23 |
BHS 29 blast select | 25 |
BHS 30 blast select | 24 |
BHS 31 blast select | 26 |
BHS 32 blast select | 6 |
Sample Type | Sc g/t |
BHS 33 blast select LZ | 6 |
BHS 34 blast select LZ | 6 |
BHS 35 blast select LZ | 14 |
BHS 36 blast select | 16 |
BHS 37 blast select | 22 |
BHS 38 blast select | 14 |
(Channel, chip samples are selected samples and are not representative of the mineralization hosted on the property.)
Bayhorse CEO, Graeme O'Neill comments, " While the Scandium values reported would not be considered enough to make a Scandium mine, in the event they are economically recoverable, the Scandium is certainly a value added mineral to any silver recovery."
The Company has established a quality control assay program at the Bayhorse Silver Mine. Production samples are split with half placed into a pulverizer, homogenized, dried, and submitted to XRF analysis with the other half retained for comparison. Check samples are sent for assay to a qualified lab. Mine samples reported are split, with one half retained for comparison. Assaying for the samples reported above was undertaken by Metsolve Labs of Langley, BC. The analytical method used for the silver analysis consisted of a 50 gram sample subjected to fire assay with gravimetric finish.
The Company advises it is not basing any decision to produce on a feasibility study of mineral reserves demonstrating economic and technical viability and also advises there is increased uncertainty and specific economic and technical risks of failure associated with any production decision.
This News Release has been prepared on behalf of the Bayhorse Silver Inc. Board of Directors, which accepts full responsibility for its contents. Dr. Stewart Jackson, P.Geo., a Qualified Person and Consultant to the Company has prepared, supervised the preparation of, or approved the technical content of this press release.
On Behalf of the Board.
Graeme O'Neill, President
604-684-3394
Bayhorse Silver Inc., a junior exploration company, has earned a 100% interest in the historic Bayhorse Silver Mine, Oregon, USA. Bayhorse is also earning a 75% interest in the past producing Bridging the Gap Project, consisting of ASARCO's historic Crown Point, Silver King, Ranger, Wyoming, Curlew, and Blackhawk silver/lead/zinc mines in Idaho's Silver Valley. The Company has an experienced management and technical team with extensive exploration and mining expertise.
Neither the TSX Venture Exchange nor its Regulation Services Provider (as that term is defined in the policies of the TSX Venture Exchange) accepts responsibility for the adequacy or accuracy of this release.